# Sending a campaign

> Check the campaign overview, fix anything that blocks sending, then send a one-time campaign or activate an always-live one, and pause or cancel it later.

When the audience and messages are ready, you send a campaign from its **Dashboard** tab. A one-time campaign is sent with **Send campaign**. An always-live campaign is switched on with **Activate campaign**. Only account admins and agency admins can do either, and it can't be undone: messages that have gone out can't be recalled.

## Check the overview

The **Campaign overview** at the top of the **Dashboard** sums up:

- **Audience**: how many customers match, or "Everyone at your store".
- **Messages**: your steps, and whether any need attention.
- **Delivery**: who the email comes from, which SMS provider and sender is used, and "Wallet push is included, at no extra cost."
- **Send window**: when the campaign may send.

Each line has a link to change it.

## Review the steps

Under **Ready to send?** (or **Ready to go live?** for an always-live campaign), each step is listed in order with how many messages it will send and a status:

- **Ready**: good to go.
- **Needs attention**: something is missing. The message tells you what, and usually links to the fix.
- **No one to reach**: nobody in the audience can get this step, for example an SMS step when nobody has a phone number. The rest of the sequence still sends.

You'll also see **Customers in audience** (or **Would enrol today** for always-live), **Total messages**, when the **First messages** go out, and for SMS the **Estimated SMS segments**. If only some customers can be reached on every channel, Leal tells you how many will get every step and how many will get only some.

### Common things that need fixing

| Message | What to do |
| ------- | ---------- |
| "Add at least one message step before sending." | Add a step on the **Steps** tab. |
| "Email subject and body are required before sending." | Finish the email. |
| "Add your sender name, reply-to address and, for your own provider, a verified From address in Settings." | Complete the **Email sender settings**. |
| "Your email sender is being set up." | Wait a minute and refresh. |
| "Connect Twilio or Brevo under Integrations before sending SMS." | Connect a provider, or remove the SMS step. |
| "No customers with email addresses match this campaign audience." | Widen the audience, or use another channel. |

## Send a one-time campaign

1. On the **Dashboard**, check the review.
2. Optional: tick **Send straight away** to skip the send window for this send only.
3. Click **Send campaign** and confirm "Send this campaign now?"

The messages are queued and go out within your send window, spaced a couple of seconds apart.

### Large sends

If a send would reach more than 500 recipients, Leal asks you to type the number in **Confirm count** before it goes. It's there to stop an accidental send to your whole list.

## Activate an always-live campaign

1. On the **Dashboard**, check the review.
2. Click **Activate campaign** and confirm.

Everyone who matches now is enrolled, and Leal keeps enrolling new customers as they start to match, checking about every ten minutes. The first messages wait a few minutes after you activate, in case you need to stop it.

An always-live campaign with nobody matching yet can still be activated. It waits for customers to qualify.

## Pause, resume or cancel

These are on the **Dashboard** under **Latest run**:

- **Pause** (always-live only): nobody new is enrolled and queued messages are held. Customers part way through a sequence wait where they are.
- **Resume**: carries on from where it stopped. Delays between steps are kept.
- **Cancel campaign**: stops it for good. Queued messages are skipped, but anything already sent can't be recalled.

## When messages are skipped

Leal checks each customer again just before each message, and skips it if:

- they've unsubscribed since they were enrolled
- they no longer match the audience (and their remaining steps are skipped too)
- a wallet step is due but they've removed the pass

## Retrying failures

If some messages failed, **Retry failed** tries again for the ones that can be retried now. Some failures can't be retried until the recipient's details or your sender settings are fixed, and Leal says so.

## Gotchas

- **Test first.** Tests can only be sent while the campaign is a draft. See [steps and messages](https://docs.getleal.com/campaigns/steps-and-messages#send-a-test).
- **Outside the window.** If you send at 9pm with a window of around 12:00, nothing goes out until tomorrow lunchtime. The run summary says when sending resumes.
