Skip to content

Sending a campaign

Check the campaign overview, fix anything that blocks sending, then send a one-time campaign or activate an always-live one, and pause or cancel it later.

When the audience and messages are ready, you send a campaign from its Dashboard tab. A one-time campaign is sent with Send campaign. An always-live campaign is switched on with Activate campaign. Only account admins and agency admins can do either, and it can't be undone: messages that have gone out can't be recalled.

Check the overview#

The Campaign overview at the top of the Dashboard sums up:

  • Audience: how many customers match, or "Everyone at your store".
  • Messages: your steps, and whether any need attention.
  • Delivery: who the email comes from, which SMS provider and sender is used, and "Wallet push is included, at no extra cost."
  • Send window: when the campaign may send.

Each line has a link to change it.

Review the steps#

Under Ready to send? (or Ready to go live? for an always-live campaign), each step is listed in order with how many messages it will send and a status:

  • Ready: good to go.
  • Needs attention: something is missing. The message tells you what, and usually links to the fix.
  • No one to reach: nobody in the audience can get this step, for example an SMS step when nobody has a phone number. The rest of the sequence still sends.

You'll also see Customers in audience (or Would enrol today for always-live), Total messages, when the First messages go out, and for SMS the Estimated SMS segments. If only some customers can be reached on every channel, Leal tells you how many will get every step and how many will get only some.

Common things that need fixing#

Message What to do
"Add at least one message step before sending." Add a step on the Steps tab.
"Email subject and body are required before sending." Finish the email.
"Add your sender name, reply-to address and, for your own provider, a verified From address in Settings." Complete the Email sender settings.
"Your email sender is being set up." Wait a minute and refresh.
"Connect Twilio or Brevo under Integrations before sending SMS." Connect a provider, or remove the SMS step.
"No customers with email addresses match this campaign audience." Widen the audience, or use another channel.

Send a one-time campaign#

  1. On the Dashboard, check the review.
  2. Optional: tick Send straight away to skip the send window for this send only.
  3. Click Send campaign and confirm "Send this campaign now?"

The messages are queued and go out within your send window, spaced a couple of seconds apart.

Large sends#

If a send would reach more than 500 recipients, Leal asks you to type the number in Confirm count before it goes. It's there to stop an accidental send to your whole list.

Activate an always-live campaign#

  1. On the Dashboard, check the review.
  2. Click Activate campaign and confirm.

Everyone who matches now is enrolled, and Leal keeps enrolling new customers as they start to match, checking about every ten minutes. The first messages wait a few minutes after you activate, in case you need to stop it.

An always-live campaign with nobody matching yet can still be activated. It waits for customers to qualify.

Pause, resume or cancel#

These are on the Dashboard under Latest run:

  • Pause (always-live only): nobody new is enrolled and queued messages are held. Customers part way through a sequence wait where they are.
  • Resume: carries on from where it stopped. Delays between steps are kept.
  • Cancel campaign: stops it for good. Queued messages are skipped, but anything already sent can't be recalled.

When messages are skipped#

Leal checks each customer again just before each message, and skips it if:

  • they've unsubscribed since they were enrolled
  • they no longer match the audience (and their remaining steps are skipped too)
  • a wallet step is due but they've removed the pass

Retrying failures#

If some messages failed, Retry failed tries again for the ones that can be retried now. Some failures can't be retried until the recipient's details or your sender settings are fixed, and Leal says so.

Gotchas#

  • Test first. Tests can only be sent while the campaign is a draft. See steps and messages.
  • Outside the window. If you send at 9pm with a window of around 12:00, nothing goes out until tomorrow lunchtime. The run summary says when sending resumes.

Still stuck?

Our team answers every message. Contact support